 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| YAEaeA|IOE3/4AE/OIE3/4 www..com Kitronix (Dong guan) Ltd. FOR APPROVAL Nu AE* EI Ee WE ARE PLEASED IN SENDDING YOU HEREWITH OUR SPECIFICATION AND DRAWING FOR YOUR APPROVAL. PLEASE RETURN TO US ONE COPY OF " FOR APPOVAL"WITH YOUR APPROVED SIGNATURES. YOUR MODULE NO.: YOUR SPEC NO.: OUR MODULE NO.: T200QFE-V44-F OUR FULL SPEC NO.: FS- T200QFE-V44-F -01 APPROVED BY APPROVED BY CUSTOMER Kitronix (Dong Guan) Ltd. No. A20, Luyi Road, Tianxin Country, Tangxia Town, Dongguan City, Guangdong Province. Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 1 OF 22 T200QFE-V44-F Product Standard LCD Module 176 x RGB x 220 Dots 2.0" TFT LCD Wide temperature With white color LED backlight With Touch Panel Kitronix (Dong Guan) Ltd. No. A20, Luyi Road, Tianxin Country, Tangxia Town, Dongguan City, Guangdong Province. Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION CONTENTS FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 2 OF 22 Page No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. DOCUMENT REVISION HISTORY GENERAL DESCRIPTION MECHANICAL SPECIFICATIONS INTERFACE SIGNALS ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS OPTICAL CHARACTERISTICS TIMING CHARACTERISTICS RELIABILITY TEST ITEM SUGGESTIONS FOR USING LCD MODULES INSPECTION STANDARD PACKING(REFERENCE ONLY) 3 4 4 6 7 7 8 10 12 13 16 22 Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 1. Document revision history : DOCUMENT REVISION DATE DESCRIPTION FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 3 OF 22 PREPARED BY APPROVED BY 01 2009.12.23 First Release. Van Ng Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 2. General Description * * * * * * FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 4 OF 22 2.0" (diagonal), 176 x RGB x 220 dots, 262k colors, Transmissive, TFT LCD module. Viewing Direction: 12 o' clock. Driving IC: LGDP4525B or equivalent TFT controller/driver. 16-bits data bus (I80 system interface). Logic voltage: 2.8V (typ.). With Touch panel. 3. Mechanical Specifications The mechanical detail is shown in Fig. 1 and summarized in Table 1 below. Table 1 Parameter Specifications 37.73(W) x 51.35(H) x 3.42(D) Outline dimensions (Exclude FPC, cables of backlight) View area 33.89(W) x 45.1(H) TP active area 33.49(W) x 44.7(H) Color TFT LCD active area 31.68(W) x 39.6(H) 176xRGBx220 Display format 176 x RGB x 220 Color configuration RGB stripes Dot pitch 0.18(RGB)(W) x 0.18(H) Weight TBD Unit mm mm mm mm dots mm TBD Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 5 OF 22 IaOUI1/4I1/4 Ooo Figure 1: Outline Drawing OE 1/2OeIuCE TPVA0 mm .3 ,uCAYAE TPVA0 mm o .6 OE (c) u1/2 XR OE YU XL YD OE OE Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 4. Interface signals Pin No. 1-8 9 10-17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Symbol [DB15-DB8] IM0 [DB7-DB0] IOVCC VCC RD WR RS CS RESET NC GND LEDA LEDK1 LEDK2 LEDK3 YU YD XR XL GND NC FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 6 OF 22 Table 2: Pin assignment Description 16-bit bi-directional data bus. " LOW" bit ; " :16 HIGH" bit ,default: :8 OPEN . 16-bit bi-directional data bus. A power supply for the internal logic circuit and for the I/O circuit. VCC = 1.8 ~ 3.3V. A power supply for the internal analog circuit. VCC = 2.2 ~ 3.3V. I80 system: Serves as a read signal and reads data at the low level. I80 system: Serves as a write signal and writes data at the rising edge. Register Select Signal (H: Data, L: Instruction) Chip select signal. 0: chip can be accessed; 1: chip cannot be accessed. Reset pin. Setting either pin low initializes the LSI. Must be reset the chip after power being supplied. No connection. Ground for the logic and analog circuit. Anode of LED backlight. Cathode of LED backlight. Terminal of touch panel. Ground for the logic and analog circuit. No connection Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 5. Absolute Maximum Ratings 5.1 FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 7 OF 22 Electrical Maximum Ratings -for IC Only Table 3: Electrical Maximum Ratings -for IC Parameter Symbol Min. Max. Unit Note Power supply voltage (VCC) VCC -0.3 +4.5 V 1 Power supply voltage (IOVCC) VCC -0.3 +4.5 V 1 Note: 1.VCC,GND must be maintained. 2.The modules may be destroyed if they are used beyond the absolute maximum ratings. Environmental Condition Table 4 Operating temperature (Topr) 5.2 Storage temperature Item Remark (Tstg) (Note 1) Min. Max. Min. Max. Ambient temperature Dry -20C +70C -30C +80C No 80% max. RH for Ta 40C Humidity (Note 1) < 50% RH for 40C < Ta Maximum operating temperature condensation Note 1: Product cannot sustain at extreme storage conditions for long time. 6. Electrical Specifications Typical Electrical Characteristics At Ta = 25 C, VCC=IOVCC= 2.6V to 3.3V, GND=0V. Table 5 Parameter Symbol Conditions Supply voltage (analog) VCC-GND Supply voltage (logic) IOVCC-GND VLED Supply voltage of white Forward current =V(BL+)LED backlight =45 mA V(BL-) Number of LED Luminance dies = 3 (on the module surface) Min. 2.6 2.6 2.9 - Typ. 2.8 2.8 3.2 150 Max. 3.3 3.3 3.5 - Unit V V V cd/m2 Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 7. Optical Characteristics FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 8 OF 22 Table 7: Optical specifications Specifications Items Symbol Condition Unit Min. Typ. Max. Contrast Ratio CR 350 TR 10 20 ms Response Time TF 15 20 ms XR - 0.651 Red YR - 0.332 XG - 0.301 Green YG - 0.585 Chromaticity Note XB - 0.133 Blue YB - 0.136 XW - 0.309 White YW - 0.345 1(3 o' clock) 45 Hor. 2(9 o' clock) Center 45 Viewing angle deg. CR=10 2(12 o' clock) 35 Ver. 1(6 o' clock) 15 NTSC ratio 61.5 % Note 1: Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63 L0: Luminance of gray level 0 CR = CR (10) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note 5. Note 2: Definition of Response Time (TR, TF): Figure 3 Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION Note 3: Viewing Angle FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 9 OF 22 Figure 4 The above " Viewing Angle"is the measuring position with Largest Contrast Ratio; not for good image quality. View Direction for good image quality is 6 O' clock. Module maker can increase the " Viewing Angle"by applying Wide View Film. Note 4: Measurement Set-Up: The LCD module should be stabilized at a given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room. Figure 5 Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 8. Timing Characteristics 8.1 80-system Bus Interface Timing Characteristics of IC Table 8: Normal Write Mode (VCC = IOVCC=2.4~3.3V) FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 10 OF 22 Figure 7. 80-system Bus Timing Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 8.2 FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 11 OF 22 Reset Operation of IC Table 9: Reset Timing Characteristics (VCC = IOVCC=2.4~3.3V) Item Symbol Unit Min. Typ. Reset low-level width tRES ms 1 Reset rise time trRES |I s Max. 10 Figure 8: Reset Timing Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 9. Reliability Test Item Test Item High temperature storage Low temperature storage High temperature /humidity storage High temperature operation Low temperature operation High temperature /humidity operation Temperature Shock Sample Type Test Condition FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 12 OF 22 Test result determinant gist the inspection of appearance and function character. Normal temperature 70 ;96H 3ae Wide temperature 80 ae 3 ;96H Normal temperature -20 ae 3 ;120H Wide temperature -30 ae 3 ;120H Normal temperature 50ae3ae ,90% 3%RH;96H Wide temperature 60ae3ae ,90% 3%RH;96H Normal temperature 60 ae 3 ;96H no objection of the function character; no fatal objection of Wide temperature 70 ae 3 ;96H the appearance. Normal temperature 0 ae 3 ;96H Wide temperature -20 ae 3 ;96H Normal temperature 40ae3ae ,90% 3%RH;96H Wide temperature 50ae3ae ,90% 3%RH;96H Normal temperature -20 ,30min? 70 ,30 3ae 3ae inspect the objections min;10cycle appearance function & the whole structure Wide temperature -30 ,30min 3ae The inspection of appearance 80 3,30min;10cycle function & the whole structure Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 10. Suggestions for using LCD modules 10.1 Handling of LCM FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 13 OF 22 1. The LCD screen is made of glass. Don't give excessive external shock, or drop from a high place. 2. If the LCD screen is damaged and the liquid crystal leaks out, do not lick and swallow. When the liquid is attach to your hand, skin, cloth etc, wash it off by using soap and water thoroughly and immediately. 3. Don't apply excessive force on the surface of the LCM. 4. If the surface is contaminated ,clean it with soft cloth. If the LCM is severely contaminated , use Isopropyl alcohol/Ethyl alcohol to clean. Other solvents may damage the polarizer . The following solvents is especially prohibited: water , ketone Aromatic solvents etc. 5. Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by water droplets, moisture condensation or a current flow in a high-humidity environment. 6. Install the LCD Module by using the mounting holes. When mounting the LCD module make sure it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I/O cable or the backlight cable. 7. Don' disassemble the LCM. t 8. To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. Be sure to ground the body when handling the LCD modules. Tools required for assembling, such as soldering irons, must be properly grounded. To reduce the amount of static electricity generated, do not conduct assembling and other work under dry conditions. The LCD module is coated with a film to protect the display surface. Exercise care when peeling off this protective film since static electricity may be generated. 9. Do not alter, modify or change the the shape of the tab on the metal frame. 10. Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be attached. Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 11. Do not damage or modify the pattern writing on the printed circuit board. FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 14 OF 22 12. Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector 13. Except for soldering the interface, do not make any alterations or modifications with a soldering iron. 14. Do not drop, bend or twist LCM. 10.2 Cautions for installing and assemabling if the module has Touch Panel 1. Use a buffer material (Gasket) between the touch panel and Front-case to protect damage and wrong operating. The dimension of the buffer material' edge between the TP V.A. edge is Min. 0.3mm. s 2. We recommend to design a case that it can' over the boundary of the active area Max. 0.5mm in order t to prevent an operation at outside of the active area which can' guarantee the specified durability, t because operation at the outside of the active area cause serious damage of a transparent. 3. When design case for installing Module, you would consider give a distance about 0.2A 0.15mm between the module edge to case inside. 4. The corners of the product are not chamfered. When positioning and fixing the product on the case, we sugguest that you would provide a R part on the conner of the case so as not to apply load on the corner of the transparent module. uC AAEA aAAI aeE| 3/4oOOIACoOo a CyCoOoO EEOCoOoO Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 10.3 Storage FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 15 OF 22 1. Store in an ambient temperature of 5 to 45 C, and in a relative humidity of 40% to 60%. Don't expose to sunlight or fluorescent light. 2. Storage in a clean environment, free from dust, active gas, and solvent. 3. Store in antistatic container. Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 11. Inspection Standard FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 16 OF 22 This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM with touch pannel. 11.1 Sample plan and Inspection condition 11.1.1 Sample plan Sampling plan according to MIL-STD-105E , normal level 2 and based on: Major defect: AQL 0.65; Minor defect: AQL 1.5. 11.1.2 Inspection condition Viewing distance for cosmetic inspection is about 30cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45 against perpendicular line. 11.2 Definition of inspection zone in LCD Inspection zones in an LCD Zone A: character/Digit area; Zone B: viewing area except Zone A (ZoneA+ZoneB=minimum Viewing area); Zone C: Outside viewing area (invisible area after assembly in customer' product); s Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer' product. Defects are classified as major defects and minor defects according to the s degree of defectiveness defined herein. 11.3 Major defects and Minor defects 11.3.1 Major defects A major defect is a defect that is likely to result in failure, or to reduce the usability of the product for its intended purpose. 11.3.1.1 Abnormal operation: modules cannot display normally; Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 17 OF 22 11.3.1.2 Line defect; 11.3.1.3 There is serious distortion or sharp burr on mechanical housing; 11.3.1.4 Glass breakage. 11.3.2 Minor defects: A minor defect is a defect that is not likely to reduce the usability of the product for its intended purpose. 11.3.2.1 Dot defect: 11.3.2.1.1 Inspection pattern : Full white, full black, red, green and blue screens; 11.3.2.1.2 Criteria :(acceptable); 1/5 Sub-pixel 3/5 ?? ?? 1/5 1/5 3/5 1/5 Note: 1. Dot defect is defined as the defective area of the dot area is larger than 50% of the dot area . And the bright dot defect must be visible through 5% ND filter. 2. Except for the allowed numbers of adjacent dots, the distance between dot defects should be more than 3mm apart. 11.3.2.1.3 The definitions of the inner display area and outer display area. 11.4 Inspection standards table: 11.4.1 Major defect Item Items to be No. Inspection Standard 1) No display 2) Display abnormally 3) Missing vertical/horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. Missing component Overall outline dimension beyond the drawing is not allowed. No more than 1.5% Classification of defects 11.4.1.1 All functional defects Major 11.4.1.2 11.4.1.3 11.4.1.4 Missing Outline dimension linearity Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 11.4.2 Cosmetic Defect (spot defect) Item No Itemsto be Clear Spots Black and white Spot defect Pinhole, Foreign Particle, polarizer Dirt Inspection Standard For dark/white spot, sizeF is defined as F =( x +y )/2 Zone Size(mm) F =0.1 0.10< F =0.15 0.15< F =0.20 F > 0.20 Zone Size(mm) F =0.1 0.10< F =0.15 0.15< F =0.25 F > 0.25 Zone Size(mm) F =0.2 0.20< F =0.4 0.4< F =0.6 F > 0.6 dot =sub-pixel Acceptable Qty I Bright dot 0 Dark dot 1 The distance of two point >5mm 11.4.3 Cosmetic Defect (linear defect) 11.4.2.4 Dot defect Item No Items to be Inspection Standard II 2 2 FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 18 OF 22 Classification of defects Minor 11.4.2.1 11.4.2.2 Clear Spots TP Dirt Acceptable Qty A B C Ignore 2 Ignore 1 0 Acceptable Qty A B C Ignore 2 Ignore 1 0 A Acceptable Qty B C Ignore 2 Ignore 1 0 Minor Minor 11.4.2.3 Dim Spots Circle shaped and dim edged defects Minor Minor Classification of defects Line defect Black line, White line, 11.4.3.1 Foreign material on polarizer Acceptable Qty zone L(Length) W(Width) A B C Ignore W=0.02 Ignore 0.02< W=0.03 L=3.0 2 Ignore 0.03< W=0.05 L=2.0 1 W> 0.05 Define as spot defect Size(mm) Minor Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION Size(mm) Foreign Material on 11.4.3.2 TP film FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 19 OF 22 The line can be seen after mobile phone in the operating condition: L(Length) Ignore L=3.0 W(Width) W=0.03 0.031/4 W=0.05 W> 0.05 Acceptable Qty zone A B C Ignore Ignore 3 Define as spot defect Minor Dim line defect Polarizer 11.4.3.3 &BL scratch TP film scratch If the scratch can be seen after mobile phone cover assembling or in the operating condition, judge by the line defect of 11.4.3.1. If the scratch can be seen only in non-operating condition or some special angle, judge by the following. Acceptable Qty zone L(Length) W(Width) A B C Ignore W=0.02 Ignore 0.02< W=0.03 L=3.0 2 Ignore 0.03< W=0.05 L=2.0 1 W> 0.05 Define as spot defect Air bubbles between glass & polarizer Acceptable Qty A B Ignore 2 1 0 Ignore C F =0.2 0.20< F =0.3 0.3< F =0.5 F > 0.5 Size(mm) Minor 11.4.3.4 Polarize Air bubble Minor 11.4.4 Chipping Defect Item No Items to be Inspection Standard Chips on corner A:LCD Glass defect Classification of defects X =0.2 11.4.4.1 Glass defect Y =S Z Disregard Minor Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. B:TP Glass defect X =3.0 Y =3.0 Z Disregard Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION Usual surface cracks A:LCD Glass defect FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 20 OF 22 X Y =3.0 X =6.0 Crack: Cracks tend to break are not allowed. Y =2.0 Z Disregard 11.4.5 Parts Defect Item No Items to be Parts contra position Inspection Standard 1 allow IC and FPC/heat-seal lead width is more than Not 50% beyond lead pattern. 2 allow chip or solder component is off center more than Not 50% of the pad outline. According to the Classification of defects Major 11.4.5.1 11.4.5.2 SMT Major 11.4.5.3 TP Defect Major 2 wing forward in the side of Visual Area The The length of wing forward inside of the Visual Area: n=0.2mm excess 3 point the distance D=20mm Not and Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 21 OF 22 3 Film impression: With operation, must be invisibility. 4 Touch panel knob writing function normally, it could be if allowed. 5 Newton ring Without operation, the color circle of Regularity or Non-regularity from the normal or slope angle of view. 1 Regularity The area of the newton ring is less than 1/3 area of the touch panel; and no character affected and line distorted after touch panel lightening. It' ok. s 2 Non-regularity area of the Newton ring is less than The the 1/2 area of touch panel with lightening. And no character affected and line 11.4.5.4 Backlight elements 11.4.5.5 Soldering 1 Illumination source flickers when lit. 2 Spots or scratches that appear when lit must be judged using LCD spot, lines and contamination standards. 3 Backlight doesn' light or color is wrong t 1 No unmelted solder paste may be present on the FPC 2 No cold solder joints, missing solder connections, oxidation or icicle. 3 No short circuits in components on FPC Major Major Kitronix (Dong guan) Ltd. PRODUCT SPECIFICATION 12. Packing (Reference only) Packing Method (1) (2) FS-T200QFE-V44-F www..com 23/Dec/2009 PAGE 22 OF 22 (3) (4) (5) (6) 1. Put module into tray cavity : 2. Tray stacking 3. Put 1 cardboard under the tray stack and 1 cardboard above: 4. Fix the cardboard to the tray stack with adhesive tape: 5. Put the tray stack into carton. 6. Carton sealing with adhesive tape. - END - |
Price & Availability of T200QFE-V44-F
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |